Acrylic Test Tube Rack: Lab Bench Build

An acrylic test tube rack is a simple looking part that fails in three predictable places: the holes, the shelf spacing and the joint between shelf and side wall. Get those right and the rack lasts a decade on a bench.

The spec below comes from a 240 rack order for a water testing laboratory in Rotterdam. The brief was short: forty tubes of 16 mm outside diameter per rack, tube bottoms visible from the front, and racks that survive being carried two at a time up a stair.

Plate thickness and rack geometry for an acrylic test tube rack

  • Base plate: 10 mm cast acrylic, 300 x 120 mm footprint
  • Side walls: 6 mm, height set by tube length plus 25 mm lift clearance
  • Tube shelf: 6 mm with 17.5 mm holes on 25 mm pitch
  • Drain gap under shelf: 12 mm so a dropped tube does not trap liquid

The base carries the load and takes the abrasion from bench movement, so it is the one part that should not be reduced to save material. A 6 mm base bows in the middle under forty filled tubes and the whole rack rocks on the bench.

Hole pitch matters more than hole size. At 25 mm pitch with 17.5 mm holes there is 7.5 mm of material between tubes, which is enough to keep the shelf from cracking when a tube is pushed in at an angle. At 20 mm pitch the ligament drops to 2.5 mm and the first crack appears within months.

How the rack is built and joined

acrylic test tube rack holding glass tubes on a laboratory bench

Racks are cut on a router, not on a laser, because a laser edge on 10 mm cast acrylic leaves a slight taper that shows as a shadow line through the clear base. Holes are drilled with a brad point bit at low speed so the exit side does not spall.

Side walls are joined with a two part acrylic adhesive on a 3 mm rabbet, not butt jointed. A butt joint on 6 mm material gives 6 mm of bond line and fails at the first knock. The rabbet triples the bonded area and holds the shelf square without a fixture.

Where acrylic is the wrong choice

Two limits decide the material. Acrylic softens at 80 to 90 C, so no autoclave, no hot water bath and no drying oven. Acrylic also stress crazes in contact with strong solvents, so racks used with acetone or xylene should be polypropylene.

For ambient bench work, cold room storage at 4 C and general sample handling, clear cast acrylic is the better buy: the operator sees the pellet and the label through the rack, and the material costs less than a machined polypropylene block of the same size.

River People casts and machines these racks in Anqing, cuts holes to a drawing you approve, and ships them packed between foam cradles so the shelves arrive square. Email oversales@rpplexiglass.com with tube size, count and footprint for a quotation.

Send your tube diameter, tube count and bench footprint to oversales@rpplexiglass.com and we will quote the rack with drawing approval before cutting.

If the rack has to drop into an existing bench module, the tolerances in our acrylic sheet cut to size service decide whether the plate fits on the first cut.

Frequently Asked Questions

What hole diameter should an acrylic test tube rack have?

Add 1 to 1.5 mm to the tube outside diameter. A 16 mm tube takes a 17.5 mm hole, which allows the tube to slide in and out without binding after the drill leaves a slight taper.

Can an acrylic rack go in an autoclave?

No. Cast acrylic softens around 80 to 90 C and distorts long before sterilization temperature. Autoclave work needs polypropylene or stainless; acrylic racks belong on the open bench and in the fridge.

Why use cast acrylic rather than extruded sheet?

Cast sheet machines without internal stress and keeps a clean edge under the drill. Extruded sheet grabs the bit, chips at the hole rim and can craze around tight hole spacing.